How to improve the basic process of hydropower ren

2022-07-22
  • Detail

Water and electricity renovation is a very important concealed project in family decoration. If it is not done well, the later repair will be troublesome, so water and electricity renovation is very important. Today, Xiaobian will bring you the basic process of water and electricity transformation and decoration. Friends who are preparing to decorate can learn about it

water and electricity renovation is a very important concealed project in family decoration. If it is not done well, the later repair will be troublesome, so water and electricity renovation is very important. Today, Xiaobian will bring you the basic process of water and electricity transformation and decoration. Friends who are preparing to decorate can learn about it

basic process of water and electricity renovation

1. Water and electricity positioning

location of switch socket and location of waterway interface. Water and electricity positioning needs to be determined according to the needs of users. The position of switches, sockets and faucets should be clearly explained to users according to the diagram, and attention should be paid to “ Water moves the sky and electricity moves the earth ” The principle is that the water pipe should go to the ceiling, and the strong and weak current should go to the ground as far as possible, and the strong and weak current should not cross each other and the parallel distance should be greater than 30 cm

2. Distribution box

distribution box controls the power consumption in the home. In the installation design, it is necessary to consider the problems of convenient use in the future, concealed safety and direct connection with external main lines. Note that the electrical lines cannot be hidden in the building bearing walls and columns

3. Electrical circuit design of sockets, switches and lamps

indoor variability should be considered in the design of sockets and switch lamps. The use of different spaces is different, so it is necessary to reduce the obstacles of re planning and design of some users in the use process, such as the impact of the movement of desks, decorative cabinets and electrical equipment on electricity and water consumption. At the same time, it is necessary to pay attention to the different prices of new buried wires and replacement wires

4. Ceiling load-bearing components

sometimes the lamps used in the home will be larger and heavier. At this time, it is necessary to pay attention to the embedded load-bearing components in the ceiling, and the load-bearing problem must be considered. It cannot be directly installed on the wooden wedge to avoid indoor unsafe factors

5. Grooving

it is easy for a good groover to make a straight groove without any hairy teeth on the edge of the groove, so it is also necessary to pay attention to the selection of a groover. Before grooving, be sure to ask the hydropower workers to mark all the water and electricity trends on the wall, and remember to check whether they are consistent with the water and electricity diagram

6. Strong and weak conduits

the junction of strong and weak conduits at home with a spacing of more than 20cm needs to be wrapped with tin foil, so as to prevent the interaction of strong and weak electricity, and to prevent hollowing in the later wall and floor tile paving

7. Waterway reconstruction

pay attention to the cleanliness of the surrounding area during waterway reconstruction. When signing the waterway reconstruction contract, it is best to indicate the materials used for waterway reconstruction. In addition, pay attention to the size of the drainage pipe in the original room during the waterway reconstruction, and the pipe connected to the drainage pipe outside is best matched with the original drainage pipe. The cold and hot water pipes should be hot on the left and cold on the right, and the spacing is generally not less than 20cm, depending on the spacing between the cold and hot water pipes of the faucet

8. The distance between hot water pipes

the distance between hot water pipes should be more than 13cm, so as to ensure that cold and hot water will not affect each other. The outlet of the hot and cold water pipe should protrude 2 to 3cm from the wall surface. Look at the inclination of the wall and the thickness of the ceramic tile to ensure that the final outlet pipe protrudes from the finished surface. At the same time, use a level ruler to check whether the two water outlets have the same horizontal and vertical wall surface

the above is the relevant knowledge of the basic process of water and electricity transformation and decoration. You can learn about water and electricity transformation. This is a very important step in decoration! I hope I can help you. If you want to know more information, please continue to pay attention to this website. Please look forward to more wonderful

哈尔滨牛皮癣医院

北京皮肤病医院

重庆银屑病医院

Copyright © 2011 JIN SHI